Search OEDI Data

UMass 2-Body WEC Techno-Economic Assessment

The University of Massachusetts (UMass) is developing a 2-body wave energy converter (WEC) device that is converting mechanical power into electricity using a mechanical motion rectifier that allows the system to couple to a flywheel. UMass has completed numerical modeling, wave t...

Previsic, M. Re Vision Consulting

Nov 19, 2024
2 Resources
0 Stars
Publicly accessible

Control-based optimization for tethered tidal kite

This submission includes three peer-reviewed (under review) papers from the researchers at North Carolina State University presenting control-based techniques to maximize effectiveness of a tethered tidal kite. Below are the abstracts of each file included in the submission. Cobb...

Vermillion, C. et al North Carolina State University

Mar 02, 2020
3 Resources
0 Stars
Publicly accessible

3D Model of the San Emidio Geothermal Area

The San Emidio geothermal system is characterized by a left-step in a west-dipping normal fault system that bounds the western side of the Lake Range. The 3D geologic model consists of 5 geologic units and 55 faults. Overlying Jurrassic-Triassic metasedimentary basement is a ~500 ...

E., J. University of Nevada

Dec 31, 2013
1 Resources
0 Stars
Publicly accessible

GEO2D Two-Dimensional Computer Model of a Ground Source Heat Pump System

This file contains a zipped file that contains many files required to run GEO2D. GEO2D is a computer code for simulating ground source heat pump (GSHP) systems in two-dimensions. GEO2D performs a detailed finite difference simulation of the heat transfer occurring within the worki...

Menart, J. Wright State University

Jun 07, 2013
3 Resources
0 Stars
Publicly accessible

RM3 Wave Tank Validation Model

An approximately 1/75th scale point absorber wave energy absorber was built to validate the testing systems of a 16k gallon single paddle wave tank. The model was build based on the RM3 design and incorporated a linear position sensor, a force transducer, and wetness detection sen...

Candon, C. and Fao, R. National Renewable Energy Laboratory

Jul 31, 2023
3 Resources
0 Stars
Publicly accessible

Performance Analysis of a Stirling Engine Hybrid Power System

This project presents the performance analysis of a photovoltaic (PV)/Stirling battery system in terms of energy efficiency, economic feasibility, and environmental sustainability. The analysis includes the dynamic start-up and cooling phases of the system, and then compares its p...

Zabalaga, P. et al National Renewable Energy Laboratory

Dec 20, 2019
7 Resources
0 Stars
Publicly accessible

Geothermal Electricity Technology Evaluation Model (GETEM) Individual Case Files and Summary Spreadsheet (GETEM version Spring 2013)

This group of files includes 10 GETEM individual scenario files and 1 summary spreadsheet. Each spreadsheet contains final data (following the revisions made between summer of 2011 and spring of 2013).

Entingh, D. et al Idaho National Laboratory

Mar 07, 2013
11 Resources
0 Stars
Publicly accessible

Pilgrim Hot Springs Building Dimensions and Energy Modeling

This dataset was created to model the anticipated heating load of a geothermal project in development for the historical site of Pilgrim Hot Springs, and adds to the history of geothermal studies at the site. Models include an historical building (Nun's Quarters), existing modern ...

Garber-Slaght, R. and Coakley, M. National Renewable Energy Laboratory (NREL)

Feb 28, 2024
2 Resources
0 Stars
Publicly accessible

Metering Best Practices Applied in the National Renewable Energy Laboratory's Research Support Facility: A Primer to the 2011 Measured and Modeled Energy Consumption Datasets

Modern buildings are complex energy systems that must be controlled for energy efficiency. The Research Support Facility (RSF) at the National Renewable Energy Laboratory (NREL) has hundreds of controllers computers that communicate with the building's various control systems to...

Sheppy. . et al National Renewable Energy Laboratory

Mar 25, 2016
4 Resources
0 Stars
Publicly accessible

University of Illinois Campus Deep Direct-Use Feasibility Study Geocellular Modeling

This submission includes 3-D geocellular model files with formation top and formation thickness data for the St. Peter and Mt. Simon Sandstones in University of Illinois Deep Direct-Use project area. An input parameters file is also included for the St. Peter Sandstone.

Damico, J. University of Illinois

May 07, 2018
5 Resources
0 Stars
Publicly accessible

Adsorption Heat Pump Coatings Investigation

In this study, a theoretical investigation was made to predict the performances of zeolite Y and SAPO-34 coatings for an adsorption cooling system operated by waste heat, under various conditions. A mathematical model developed and tested previously for coatings of A and X type ze...

Tatlier, M. Istanbul Technical University

May 22, 2020
2 Resources
0 Stars
Publicly accessible

Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber)

Contains the Reference Model 3 (RM3) scaled scale geometry files of the Wave Point Absorber, developed by the Reference Model Project (RMP). These scaled geometry files are saved as SolidWorks assembly, IGS, and STEP files, and require a CAD program to view. The scaled RM3 device ...

Neary, V. et al Sandia National Laboratories

Sep 30, 2014
7 Resources
0 Stars
Publicly accessible

LCOE Baseline for Wave Carpet WEC Device

This is an LCOE (levelized cost of energy) baseline assessment for the Wave Carpet.

Previsic, M. et al Re Vision Consulting

Jul 26, 2017
2 Resources
0 Stars
Publicly accessible

3D Model of the McGinness Hills Geothermal Area

The McGinness Hills geothermal system lies in a ~8.5 km wide, north-northeast trending accommodation zone defined by east-dipping normal faults bounding the Toiyabe Range to the west and west-dipping normal faults bounding the Simpson Park Mountains to the east. Within this broad ...

E. Faulds, J. University of Nevada

Dec 31, 2013
1 Resources
0 Stars
Publicly accessible

BENEFIT with Northeastern University: HVAC Hardware-in-the-Loop Experimental Testing of Heat Pump and Air Conditioner

This dataset includes HVAC Hardware-in-the-Loop (HIL) experimental results for a single stage, SEER 16, HSPF 9.5, 3-ton single-speed air source heat pump with 15 kW of backup auxiliary heating tested in both cooling and heating mode, and a two-stage, SEER 21, 2-ton central air con...

Ramaraj and SparnNational Renewable Energy Laboratory

Sep 10, 2024
25 Resources
0 Stars
Publicly accessible

Simulation Tools for Modeling Thermal Spallation Drilling on Multiple Scales

Widespread adoption of geothermal energy will require access to deeply buried resources in granitic basement rocks at high temperatures and pressures. Exploiting these resources necessitates novel methods for drilling, stimulation, and maintenance, under operating conditions that ...

Walsh, S. et al Lawrence Livermore National Laboratory

Jan 01, 2012
1 Resources
0 Stars
Publicly accessible

Assessing Total Cost of Driving Competitiveness of Zero-Emission Trucks

This file includes supporting data on modeled medium and heavy-duty vehicle (MHDV) stock, sales, energy consumption, greenhouse gas (GHG) emissions, and total cost of driving (TCD) for the scenarios presented in "Assessing Total Cost of Driving Competitiveness of Zero-Emission Tru...

Ledna. . et al Center for Integrated Mobility Sciences

Feb 27, 2024
1 Resources
0 Stars
Publicly accessible

Subsurface Geological Information and Models in support of Feasibility Study of Direct District Heating for the Cornell Campus Utilizing Deep Geothermal Energy

This purpose of this set of entries is to group together the materials and analytical methods used in the assessment of the natural rock properties within and surrounding two potential reservoirs.

Jordan, T. et al Cornell University

Oct 27, 2019
27 Resources
0 Stars
Publicly accessible

CalWave Device Behavior in Different Sea States from Scaled Tank Testing

This submission contains a summary of tank test derived WEC device behavior in different irregular sea states. CalWave sought to conduct experimental tank testing of scaled prototype units early on in the design process to obtain a first estimation of device performance for sea ...

Boerner, T. and Murray, B. CalWave Power Technologies Inc.

Mar 30, 2018
1 Resources
0 Stars
Publicly accessible

Newberry FORGE: 3D Gravity Density Model for Newberry Volcano

These data are Pacific Northwest National Lab inversions of an amalgamation of two surface gravity datasets: Davenport-Newberry gravity collected prior to 2012 stimulations and Zonge International gravity collected for the project "Novel use of 4D Monitoring Techniques to Improve...

Bonneville, A. Pacific Northwest National Laboratory

Mar 11, 2016
1 Resources
0 Stars
Publicly accessible

Deep Green Unannotated Protein Structures

The Deep Green list is based on the identification and curation of conserved unannotated proteins in three green lineage (Viridiplantae) model organisms; Arabidopsis thaliana, Chlamydomonas reinhardtii, and Setaria viridis. Preliminary characterization of Deep Green proteins and g...

Knoshaug. . et al National Renewable Energy Laboratory

Apr 20, 2023
4 Resources
0 Stars
Publicly accessible

Triton: Survivability Enhancement of a Multi-Mode Point Absorber

The overall goal of this project was to design and validate a survival mode for the Triton WEC that allows for a reduction in peak loads, while simultaneously allowing for a reduction of capital cost due to the elimination of overdesign to account for uncertainty. In addition, the...

Mundon, T. and Rosenberg, B. Oscilla Power, Inc.

Sep 28, 2018
11 Resources
0 Stars
Publicly accessible

TidGen MHK Generator Composite Fatigue Analysis Procedure

A procedure was described for performing a fatigue analysis of composite foils for an MHK generator. The steps included generating load data, S-N (Stress versus Number of cycles to failure) diagrams through fatigue testing, cycle counts, damage versus load, and cumulative damage. ...

Krumpe, A. ORPC Inc.

Apr 14, 2020
2 Resources
0 Stars
Publicly accessible

Optimization of Marine Energy Conversion Systems Through Modeling, Optimization, and CHIL Validation

The work aims to achieve optimal tidal energy conversion through a comprehensive approach of modeling, optimization, and control hardware-in-the-loop (CHIL) validation. By developing accurate models and employing optimization techniques, it seeks to identify efficient system confi...

Luo, F. et al Stony Brook University

Jul 17, 2023
6 Resources
0 Stars
Publicly accessible

Wave Tank Testing of 1-DoF Heaving Buoy for Controls Validation Purposes

This submission includes the wave tank testing data used to validate the controls optimization efforts of a heaving 1-DoF buoy.