Search OEDI Data

Showing results 51 - 75 of 261.
Show results per page.
Order by:
Available Now:
Research Areas
Accessibility
Data Type
Organization
Source
"inverse design"×

Aquantis 2.5 MW Ocean Current Generation Device Scaled Tank Test Design and Results

Aquantis 2.5 MW Ocean Current Generation Device, Tow Tank Dynamic Rig Structural Analysis Results. This is the detailed documentation for scaled device testing in a tow tank, including models, drawings, presentations, cost of energy analysis, and structural analysis. This datase...
Swales, H. et al Dehlsen Associates, LLC
Jun 03, 2015
46 Resources
0 Stars
Publicly accessible

Laboratory Evaluation of EGS Shear Stimulation-Test 001

This is the results of an initial setup-shakedon test in order to develop the plumbing system for this test design. a cylinder of granite with offset holes was jacketed and subjected to confining pressure and low temperature (85C) and pore water pressure. Flow through the sample w...
Bauer, S. Sandia National Laboratories
Jul 29, 2014
1 Resources
0 Stars
Publicly accessible

University of Illinois Campus Deep Direct-Use Feasibility Study Design of Injection Well #1 (CCS1)

Includes specification sheet, wellbore geometry, and drilling fluids at section target depth associated with the design of Injection Well #1 (CCS1) for the Illinois Basin Decatur Project (IBDP).
Greenberg, S. University of Illinois
Mar 30, 2018
1 Resources
0 Stars
Publicly accessible

AeroDyn V15.04: Design Tool for Wind and MHK Turbines

AeroDyn is a time-domain wind and MHK turbine aerodynamics module that can be coupled into the FAST version 8 multi-physics engineering tool to enable aero-elastic simulation of horizontal-axis wind turbines. AeroDyn V15.04 has been updated to include a cavitation check for MHK tu...
Murray, R. et al National Renewable Energy Laboratory
Apr 28, 2017
1 Resources
0 Stars
Publicly accessible

Advanced TidGen Power System Material Characterization Program

The TidGen Power System generates emission-free electricity from tidal currents and connects directly into existing grids using smart grid technology. The power system consists of three major subsystems: shore-side power electronics, mooring system, and turbine generator unit (TGU...
Marnagh, C. and McEntee, J. Ocean Renewable Power Company
Jun 14, 2018
2 Resources
0 Stars
Publicly accessible

Utah FORGE Project 3-2535: Building a 3D Resistivity Model for Simulation and Survey Design of EM Measurements

The included report outlines the creation of three 3D resistivity models that will be used to determine the sensitivity of EM measurements for the hypothetical stimulated reservoir at FORGE as well as for EM survey design. FORGE project 3-2535 is planning on using a casing source ...
Alumbaugh, D. et al Lawrence Berkeley National Laboratory
Dec 01, 2022
5 Resources
0 Stars
Publicly accessible

M3 Wave DMP/APEX WEC Device Configuration Drawings

Configurations as tested and modeled in final phase of project for the Delos-Reyes Morrow Pressure Device (DMP), commercialized by M3 Wave LLC as "APEX."
Morrow, M. and Delos-Reyes, M. M3 Wave
Aug 08, 2017
1 Resources
0 Stars
Publicly accessible

Measured Performance of a Varied Airflow Small-Diameter Duct System

In this study, researchers with the U.S. Department of Energy's Building America team IBACOS built on research previously done in two new-construction unoccupied test houses-one in Pittsburgh, Pennsylvania (Poerschke and Stecher 2014) and one in Fresno, California (Stecher and Poe...
Poerschke, A. Ibacos Innovation
Apr 27, 2016
5 Resources
0 Stars
Publicly accessible

Reference Model 6 Full Scale Geometry (RM6: Oscillating Water Column)

Contains the Reference Model 6 (RM6) full scale geometry files of the Oscillating Water Column, developed by the Reference Model Project (RMP). These full scale geometry files are saved as SolidWorks assembly, IGS, and STEP files, and require a CAD program to view. This data was g...
Neary, V. et al Sandia National Laboratories
Sep 30, 2014
4 Resources
0 Stars
Publicly accessible

Advanced TidGen Power System LCOE Calculations and System Overview

The TidGen Power System generates emission-free electricity from tidal currents and connects directly into existing grids using smart grid technology. The power system consists of three major subsystems: shore-side power electronics, mooring system, and turbine generator unit (TGU...
Marnagh, C. and McEntee, J. Ocean Renewable Power Company
Jun 14, 2018
4 Resources
0 Stars
Publicly accessible

HERO WEC V1.0 SolidWorks Model

The attached zip file includes a SolidWorks pack-and-go assembly of NREL's HERO WEC (hydraulic and electric reverse osmosis wave energy converter) V1.0. This model does not include all aspects of the design (i.e. RO (reverse osmosis) system, electrical enclosure, hose, cable) it o...
Jenne, S. National Renewable Energy Laboratory
Aug 12, 2022
2 Resources
0 Stars
Publicly accessible

Advanced TidGen Power System Summary Presentation

The TidGen Power System generates emission-free electricity from tidal currents and connects directly into existing grids using smart grid technology. The power system consists of three major subsystems: shore-side power electronics, mooring system, and turbine generator unit (TGU...
Marnagh, C. and McEntee, J. Ocean Renewable Power Company
May 10, 2018
1 Resources
0 Stars
Publicly accessible

FOSWEC v2: System identification and control testing at Hinsdale Wave Research Laboratory

This report summarizes the design and execution of a wave tank test of the floating oscillating surge wave energy converter (FOSWEC) in the O.H. Hinsdale Wave Research Laboratory Directional Wave Basin at Oregon State University. This device, which uses two "flaps" that pivot abou...
Coe, R. et al Sandia National Laboratories
Feb 01, 2020
2 Resources
0 Stars
Publicly accessible

PoroTomo Distributed Temperature Sensing (DTS) Measurements made in Brady Observation Well 56-1

This submission is a follow-up to Distributed Temperature Sensing (DTS) measurements made in Brady observation well 56-1 during the PoroTomo field experiment conducted in March, 2016. The measurements in this data set were made on August 24, 2018 over an approximately 20 hour per...
Kratt, C. et al Oregon State University
Jan 09, 2019
6 Resources
0 Stars
Publicly accessible

North and South Dakota High Resolution 50m Wind Resource

Annual average wind resource potential for North and South Dakota at a 50 meter height in a GIS shapefile and links to US national wind resource information tools. This data set was produced and validated by NREL using their WRAM model.
Langle, N. and Lopez, A. National Renewable Energy Laboratory
Nov 25, 2014
4 Resources
0 Stars
Curated

Spooling control design for flight optimization of tethered tidal kites

This submission includes three peer-reviewed (under review) papers from the researchers at North Carolina State University presenting different control-based techniques to maximize the efficiency and robustness of a tethered energy-harvesting kite. Below are the abstracts of each ...
Daniels, J. et al North Carolina State University
Sep 16, 2019
3 Resources
0 Stars
Publicly accessible

LandRAY PTO Testing Utilizing the NREL NWTC 5MW Dynamometer

The overarching project objective is to demonstrate the feasibility of using an innovative PowerTake-Off (PTO) Module in Columbia Power's utility-scale wave energy converter (WEC). The PTO Module uniquely combines a large-diameter, direct-drive, rotary permanent magnet generator; ...
Lenee-Bluhm, P. and Rhinefrank, K. Columbia Power Technologies, Inc.
Jun 13, 2016
3 Resources
0 Stars
Publicly accessible

Brookfield Homes Passive House Performance Evaluation

TO4 3.1.3: Brookfield Homes Short-Term Results TO5 3.1.3: Brookfield Passive House Monitoring To further define its market position on high performance homebuilding, Brookfield worked with IBACOS and the Building America program to design and construct a Passive House (PH) certif...
Beach, R. et al Ibacos Innovation
Apr 27, 2016
4 Resources
0 Stars
Publicly accessible

LandRAY PTO Test Plans with NREL NWTC 5 MW Dynamometer

The overarching project objective is to demonstrate the feasibility of using an innovative PowerTake-Off (PTO) Module in Columbia Power's utility-scale wave energy converter (WEC). The PTO Module uniquely combines a large-diameter, direct-drive, rotary permanent magnet generator; ...
Prudell, J. et al Columbia Power Technologies, Inc.
Feb 29, 2016
5 Resources
0 Stars
Publicly accessible

Desert Peak Geodatabase for Geothermal Exploration Artificial Intelligence

These files contain the geodatabases related to the Desert Peak Geothermal Field. It includes all input and output files used in the project. The files include data categories of raw data, pre-processed data, and analysis (post-processed data). In each of these categories there ar...
Moraga, J. et al Colorado School of Mines
Apr 27, 2021
3 Resources
0 Stars
Publicly accessible

Utah FORGE Project 3-2535: Modeling Studies of Energized Steel-Casing Source EM Method for Detecting Stimulated Zone

Numerical modeling Studies for electromagnetic (EM) Data Acquisition Survey Design this milestone report describes the 3D modeling studies of energized steel-casing source electromagnetic method for detecting stimulated zone at the Utah FORGE Site. FORGE project 3-2535 is planning...
Um, E. et al Lawrence Berkeley National Laboratory
Feb 06, 2023
4 Resources
0 Stars
Publicly accessible

Deep Direct-Use Feasibility Study Energy Demand Characterization and Surface Plant Modeling for West Virginia University

This dataset provides information gathered to determine end use load and assessment of existing district heating systems (DHS). It also provides Aspen simulation files used to model hybrid natural gas geothermal district heating and cooling (GDHC) system along with Exchange Design...
Garapati, N. West Virginia University
Jan 09, 2020
4 Resources
0 Stars
Publicly accessible

Simulations of Brady's-Type Fault Undergoing CO2 Push-Pull: Pressure-Transient and Sensitivity Analysis

Input and output files used for fault characterization through numerical simulation using iTOUGH2. The synthetic data for the push period are generated by running a forward simulation (input parameters are provided in iTOUGH2 Brady GF6 Input Parameters.txt [InvExt6i.txt]). In gene...
Jung, Y. and Doughty, C. Lawrence Berkeley National Laboratory
Mar 09, 2018
11 Resources
0 Stars
Publicly accessible

Sup3rWind Data (CONUS)

This data contains paired European Centre for Medium-Range Weather Forecasts Reanalysis version 5 (ERA5) and the Wind Integration National Dataset Toolkit (WTK) images for 2007 and 2010 over two regions in the US, with domain sizes ~800x800 (latitudes from 25.89 to 41.58, and long...
Sinha, S. et al National Renewable Energy Lab NREL
Jul 16, 2024
6 Resources
0 Stars
Curated

Wind and Structural Loads on Parabolic Trough Solar Collectors at Nevada Solar One

Wind loading is a main contributor to structural design costs of Concentrating Solar Power (CSP) collectors, such as heliostats and parabolic troughs. These structures must resist the mechanical forces generated by turbulent wind. At the same time, the reflector surfaces must exhi...
Egerer, U. et al National Renewable Energy Laboratory (NREL)
Oct 01, 2021
4 Resources
0 Stars
Publicly accessible
<< Previous1234567Next >>