"Womp Womp! Your browser does not support canvas :'("

Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber)

Publicly accessible License 

Contains the Reference Model 3 (RM3) scaled scale geometry files of the Wave Point Absorber, developed by the Reference Model Project (RMP). These scaled geometry files are saved as SolidWorks assembly, IGS, and STEP files, and require a CAD program to view. The scaled RM3 device was tested at the Scripps Institution of Oceanography at the University of California at San Diego wave tank, details of which are described in the included test report. The scale of the geometries included in this submission are at a 1:33 scale compared to the full scale geometry. This data was generated upon completion of the project on September 30, 2014.

The Reference Model Project (RMP), sponsored by the U.S. Department of Energy (DOE), was a partnered effort to develop open-source MHK point designs as reference models (RMs) to benchmark MHK technology performance and costs, and an open-source methodology for design and analysis of MHK technologies, including models for estimating their capital costs, operational costs, and levelized costs of energy. The point designs also served as open-source test articles for university researchers and commercial technology developers. The RMP project team, led by Sandia National Laboratories (SNL), included a partnership between DOE, three national laboratories, including the National Renewable Energy Laboratory (NREL), Pacific Northwest National Laboratory (PNNL), and Oak Ridge National Laboratory (ORNL), the Applied Research Laboratory of Penn State University, and Re Vision Consulting.

Reference Model 3 (RM3) is a wave point absorber, also referred to as a wave power buoy, that was designed for a reference site located off the shore of Eureka in Humboldt County, California. The design of the device consists of a surface float that translates (oscillates) with wave motion relative to a vertical column spar buoy, which connects to a subsurface reaction plate. This two-body point absorber converts wave energy into electrical power predominately from the device?s heave oscillation induced by incident waves; the float is designed to oscillate up and down the vertical shaft up to 4 m. The bottom of the reaction plate is about 35 m below the water surface. The device is targeted for deployment in water depths of 40 m to 100 m. The point absorber is also connected to a mooring system to keep the floating device in position.

Citation Formats

Sandia National Laboratories. (2014). Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber) [data set]. Retrieved from https://dx.doi.org/10.15473/1818910.
Export Citation to RIS
Neary, Vince, Yu, Yi-Hsiang, Epler, Jeffrey, Shoele, Kourosh, Previsic, Mirko, Lawson, Michael, and Li, Ye. Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber). United States: N.p., 30 Sep, 2014. Web. doi: 10.15473/1818910.
Neary, Vince, Yu, Yi-Hsiang, Epler, Jeffrey, Shoele, Kourosh, Previsic, Mirko, Lawson, Michael, & Li, Ye. Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber). United States. https://dx.doi.org/10.15473/1818910
Neary, Vince, Yu, Yi-Hsiang, Epler, Jeffrey, Shoele, Kourosh, Previsic, Mirko, Lawson, Michael, and Li, Ye. 2014. "Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber)". United States. https://dx.doi.org/10.15473/1818910. https://mhkdr.openei.org/submissions/364.
@div{oedi_4483, title = {Reference Model 3 Scaled Geometry (RM3: Wave Point Absorber)}, author = {Neary, Vince, Yu, Yi-Hsiang, Epler, Jeffrey, Shoele, Kourosh, Previsic, Mirko, Lawson, Michael, and Li, Ye.}, abstractNote = {Contains the Reference Model 3 (RM3) scaled scale geometry files of the Wave Point Absorber, developed by the Reference Model Project (RMP). These scaled geometry files are saved as SolidWorks assembly, IGS, and STEP files, and require a CAD program to view. The scaled RM3 device was tested at the Scripps Institution of Oceanography at the University of California at San Diego wave tank, details of which are described in the included test report. The scale of the geometries included in this submission are at a 1:33 scale compared to the full scale geometry. This data was generated upon completion of the project on September 30, 2014.

The Reference Model Project (RMP), sponsored by the U.S. Department of Energy (DOE), was a partnered effort to develop open-source MHK point designs as reference models (RMs) to benchmark MHK technology performance and costs, and an open-source methodology for design and analysis of MHK technologies, including models for estimating their capital costs, operational costs, and levelized costs of energy. The point designs also served as open-source test articles for university researchers and commercial technology developers. The RMP project team, led by Sandia National Laboratories (SNL), included a partnership between DOE, three national laboratories, including the National Renewable Energy Laboratory (NREL), Pacific Northwest National Laboratory (PNNL), and Oak Ridge National Laboratory (ORNL), the Applied Research Laboratory of Penn State University, and Re Vision Consulting.

Reference Model 3 (RM3) is a wave point absorber, also referred to as a wave power buoy, that was designed for a reference site located off the shore of Eureka in Humboldt County, California. The design of the device consists of a surface float that translates (oscillates) with wave motion relative to a vertical column spar buoy, which connects to a subsurface reaction plate. This two-body point absorber converts wave energy into electrical power predominately from the device?s heave oscillation induced by incident waves; the float is designed to oscillate up and down the vertical shaft up to 4 m. The bottom of the reaction plate is about 35 m below the water surface. The device is targeted for deployment in water depths of 40 m to 100 m. The point absorber is also connected to a mooring system to keep the floating device in position.}, doi = {10.15473/1818910}, url = {https://mhkdr.openei.org/submissions/364}, journal = {}, number = , volume = , place = {United States}, year = {2014}, month = {09}}
https://dx.doi.org/10.15473/1818910

Details

Data from Sep 30, 2014

Last updated Sep 16, 2021

Submitted Sep 2, 2021

Organization

Sandia National Laboratories

Contact

Vince Neary

Authors

Vince Neary

Sandia National Laboratories

Yi-Hsiang Yu

National Renewable Energy Laboratory

Jeffrey Epler

Revision Consulting

Kourosh Shoele

Revision Consulting

Mirko Previsic

Revision Consulting

Michael Lawson

National Renewable Energy Laboratory

Ye Li

National Renewable Energy Laboratory

DOE Project Details

Project Name Reference Model Project

Project Lead Jeff Rieks

Project Number FY13 AOP 1.2.5.1

Share

Submission Downloads