UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data
**Overview**
Sequence 5: Sweep Wind Speed (F,P)
This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed was
ramped from 5 m/s to 25 m/s by the wind tunnel operator. This was repeated with a decreasing
ramp. The yaw angle was maintained at 0°. The blade tip pitch was 3° or 6°. The rotor rotated at
72 RPM. Blade pressure and probe measurements were collected for both pitch angles. The five-hole
probes were removed and the plugs were installed for another 3° pitch case. Plastic tape 0.03
mm thick was used to smooth the interface between the plugs and the blade. The teeter dampers
were replaced with rigid links, and these two channels were flagged as not applicable by setting
the measured values in the data file to ?99999.99 Nm. The teeter link load cell was pre-tensioned
to 40,000 N. During post-processing, the probe channels were set to read -99999.99. The 6-
minute campaigns were named using the sequence designation 5, followed by DN or UP, which
indicates the wind speed ramp direction. The next four digits are 0000, and the sequence digit is
at the end.
**Data Details**
File naming information can be found in the attached Word document "Sequence 5 Filename Key", copied from the Phase VI Test Report.
Citation Formats
TY - DATA
AB - **Overview**
Sequence 5: Sweep Wind Speed (F,P)
This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed was
ramped from 5 m/s to 25 m/s by the wind tunnel operator. This was repeated with a decreasing
ramp. The yaw angle was maintained at 0°. The blade tip pitch was 3° or 6°. The rotor rotated at
72 RPM. Blade pressure and probe measurements were collected for both pitch angles. The five-hole
probes were removed and the plugs were installed for another 3° pitch case. Plastic tape 0.03
mm thick was used to smooth the interface between the plugs and the blade. The teeter dampers
were replaced with rigid links, and these two channels were flagged as not applicable by setting
the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned
to 40,000 N. During post-processing, the probe channels were set to read -99999.99. The 6-
minute campaigns were named using the sequence designation 5, followed by DN or UP, which
indicates the wind speed ramp direction. The next four digits are 0000, and the sequence digit is
at the end.
**Data Details**
File naming information can be found in the attached Word document "Sequence 5 Filename Key", copied from the Phase VI Test Report.
AU - Fingersh, Lee
DB - Open Energy Data Initiative (OEDI)
DP - Open EI | National Renewable Energy Laboratory
DO - 10.21947/1481780
KW - a2e
KW - atmosphere to electrons
KW - wind
KW - weto
KW - eere
KW - uae6
KW - Unsteady Aerodynamics Experiment Phase VI NREL-NASA Ames Wind Tunnel Experiment
KW - UAE6
KW - Wind Tunnel Tests Data
KW - Sequence 5
KW - Raw Data
KW - z26
KW - 00
LA - English
DA - 2018/11/12
PY - 2018
PB - Wind Energy Technologies Office (WETO)
T1 - UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data
UR - https://doi.org/10.21947/1481780
ER -
Fingersh, Lee. UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data. Wind Energy Technologies Office (WETO), 12 November, 2018, A2E. https://doi.org/10.21947/1481780.
Fingersh, L. (2018). UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data. [Data set]. A2E. Wind Energy Technologies Office (WETO). https://doi.org/10.21947/1481780
Fingersh, Lee. UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data. Wind Energy Technologies Office (WETO), November, 12, 2018. Distributed by A2E. https://doi.org/10.21947/1481780
@misc{OEDI_Dataset_4192,
title = {UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data},
author = {Fingersh, Lee},
abstractNote = {**Overview**
Sequence 5: Sweep Wind Speed (F,P)
This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed was
ramped from 5 m/s to 25 m/s by the wind tunnel operator. This was repeated with a decreasing
ramp. The yaw angle was maintained at 0°. The blade tip pitch was 3° or 6°. The rotor rotated at
72 RPM. Blade pressure and probe measurements were collected for both pitch angles. The five-hole
probes were removed and the plugs were installed for another 3° pitch case. Plastic tape 0.03
mm thick was used to smooth the interface between the plugs and the blade. The teeter dampers
were replaced with rigid links, and these two channels were flagged as not applicable by setting
the measured values in the data file to ?99999.99 Nm. The teeter link load cell was pre-tensioned
to 40,000 N. During post-processing, the probe channels were set to read -99999.99. The 6-
minute campaigns were named using the sequence designation 5, followed by DN or UP, which
indicates the wind speed ramp direction. The next four digits are 0000, and the sequence digit is
at the end.
**Data Details**
File naming information can be found in the attached Word document "Sequence 5 Filename Key", copied from the Phase VI Test Report.},
url = {https://a2e.energy.gov/data/uae6/uae6.z26.00},
year = {2018},
howpublished = {A2E, Wind Energy Technologies Office (WETO), https://doi.org/10.21947/1481780},
note = {Accessed: 2025-05-07},
doi = {10.21947/1481780}
}
https://dx.doi.org/10.21947/1481780
Details
Data from Nov 12, 2018
Last updated Mar 27, 2020
Submitted Nov 12, 2018
Organization
Wind Energy Technologies Office (WETO)
Contact
Lee Fingersh
303.384.6929
Authors
Original Source
https://a2e.energy.gov/data/uae6/uae6.z26.00Research Areas
Keywords
a2e, atmosphere to electrons, wind, weto, eere, uae6, Unsteady Aerodynamics Experiment Phase VI NREL-NASA Ames Wind Tunnel Experiment, UAE6, Wind Tunnel Tests Data, Sequence 5, Raw Data, z26, 00DOE Project Details
Project Name Wind Data Hub
Project Number 67025